Skip to content

Anodising colours: how to colour aluminium

Natural, black, bronzes, gold or bright colours, inside the metal itself. And the same shade order after order.

Speak to a technician. Monday to Friday, 8:00 to 17:00 (CET).

Carta de colores de anodizado abierta en abanico

Which colours

The range, and where each colour lasts

  • NaturalThe silver of aluminium, matt or bright depending on the preparation. The most requested.
  • Bronzes, champagne, graphite and blackElectrolytic, the most stable in sunlight. For outdoor use, the safe choice.
  • Interference blues, greens and goldsAlso very stable outdoors, with a narrower range of shades.
  • Gold, blue, red, green, violetBright colours, with organic dye. Some lose intensity in the sun: better indoors, or tested first.
  • WhiteThere is no white anodising. If you need white, what you are looking for is powder coating.
Black anodising

How it goes in

The colour is inside the layer

Anodising leaves the layer full of pores. The colour goes in there, and then it is sealed. That is why it does not peel like paint.

There are three ways of colouring. We tell you which suits you depending on where the part goes.

Electrolytic

Metal salts at the bottom of the pores. It gives champagne, bronzes, graphite and black, and it is the most stable in sunlight.

Organic dye

Dyes absorbed by the pores. The widest range (red, blue, green, gold, violet), better for indoor use.

Interference

The shade comes from how light bounces inside the pore. Very stable blues, greens and golds.

The codes

What «natural E6 C0» means

It is the usual way to specify anodising on a drawing: surface pre-treatment plus colour.

The letter E indicates how the surface is prepared before anodising, and the C, the colour. «E6» is a chemical satin finish: an etch that leaves the aluminium matt and even, the most common pre-treatment. «C0» means no colour: natural silver anodising.

  • E0Degreasing only: the marks on the part remain.
  • E1 to E5Grinding, brushing, polishing or combinations of them.
  • E6Chemical satin finish: matt and even.
  • C0Natural, no colour.
  • C31 to C35From light bronze to black, with electrolytic colouring.

Order after order

The same shade in every batch

Getting a colour once is easy. Repeating it is the hard part.

The shade changes with the alloy, the preparation and the thickness. So we agree a master sample with you, measure every batch against it and keep the reference. The difference between batches stays below a ΔE*ab of 1.0, which the eye does not notice.

For production runs, we make colour samples on your own part, free of charge.

Colour anodising

RAL and Pantone

Can you match my RAL or Pantone colour?

Anodising does not work from a RAL chart the way paint does: the colour depends on the alloy, the pre-treatment and the thickness. We work to your physical sample or your reference, measure the colour difference with a spectrophotometer and show you the result on your part before production.

Frequently asked questions

Frequently asked questions

What is natural anodising?

Anodising with no colour: the aluminium keeps its silver, matt or bright depending on the preparation. On drawings it is specified as «C0»; «E6 C0» is natural with a chemical satin finish.

Can aluminium be anodised white?

No. Anodising is translucent and cannot give a white like paint. For white, powder coating.

Does the colour come out the same on every part?

If they are the same alloy and have the same preparation, yes. That is why we agree a master sample and measure every batch against it.

Does colour anodising fade?

Bronzes, champagne and electrolytic black barely change in the sun. Some bright colours do lose intensity: that is why we recommend them for indoor use.

Can the colour of an anodised part be changed?

Yes, by stripping the layer and anodising again. The part loses some material: if it has tight tolerances, it is worth knowing beforehand.

Ask for colour samples on your part

For production runs, they are free. Call +34 937 55 62 77, tell us the colour and the alloy, and we will prepare the samples before production.

Speak to a technician. Monday to Friday, 8:00 to 17:00 (CET). Leave your number and we will call you back within the hour.

Direct contact

Plant
Carrer dels Remences, 114, 08304 Mataró (Barcelona)